Model SFP Optical Transceiver » SFP Transceiver » MODUL SFP TRANSCEIVER - Double Fiber

  • MODUL SFP TRANSCEIVER - Double Fiber

  • MODEL:155/1.25G Mbps SFP Optical Transceiver 20Km with DDM

Feature: 

  • SFP package with LC connector
  • 1310nm FP laser and PIN photo detector
  • Up to 20Km transmission on SMF
  • +3.3V single power supply
  • LVPECL compatible data input/output interface
  • Low EMI and excellent ESD protection
  • laser safety standard IEC-60825 compliant
  • Compatible with RoHS
  • Digital Diagnostic SFF-8472 compliant 

Application: 

  • Ethernet 
  • Telecom
  • Fiber Channel 

Ordering information

HHD-G3115-2-LC 155M 1310/850nmnm 2KM/550M MM LC SFP 0~70 FP+PIN
HHD-G3115-20-LC 155M 1310nm 20KM SM LC SFP 0~70 FP+PIN
HHD-G3112-2-LC 1.25G 850nmnm 550M MM LC SFP 0~70 FP+PIN
HHD-G3112-20-LC 1.25G 1310nm 20KM SM LC SFP 0~70 FP+PIN
HHD-G3112-40-LC 1.25G 1310nm 40KM SM LC SFP 0~70 DFB+PIN
HHD-G3112-60-LC 1.25G 1310nm 60KM SM LC SFP 0~70 DFB+PIN
HHD-G3112-80-LC 1.25G 1310nm 80KM SM LC SFP 0~70 DFB+PIN
HHD-G3112-120-LC 1.25G 1310nm 120KM SM LC SFP 0~70 DFB+PIN

 

1. Feature: 

  • SFP package with LC connector 
  • 1310nm FP laser and PIN photo detector 
  • Up to 20Km transmission on SMF 
  • +3.3V single power supply 
  • LVPECL compatible data input/output interface 
  • Low EMI and excellent ESD protection 
  • laser safety standard IEC-60825 compliant 
  • Compatible with RoHS 
  • Digital Diagnostic SFF-8472 compliant 

2. Application: 

  • Ethernet 
  • Telecom
  • Fiber Channel 

3.AbsoluteMaximumRatings:

Parameter Symbol Minimum Maximum Units
Storage Temperature Tst -40 +85 °C
Supply Voltage Vcc 0 +3.6 V
Operating Relative Humidity RH 5 95 %

 

4. Operation Environment:

5. Optical Characteristics:

                                  (Ambient Operating Temperature 0°Cto+70ºC,Vcc=3.3V)

6. Electrical Characteristics:

7. EEPROM INFORMATION(A0):

8. Diagnostics:

9. Pin Description:

NOTES:

1. TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.

2. TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are: Low (0~0.8V): Transmitter on (>0.8V, <2.0V): Undefined High (2.0~3.3V): Transmitter Disabled Open: Transmitter Disabled

3.         MOD-DEF 0,1,2 are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on the host board. The pull-up voltage shall be VccT or VccR.

MOD-DEF 0 is grounded by the module to indicate that the module is present

MOD-DEF 1 is the clock line of two wire serial interface for serial ID

MOD-DEF 2 is the data line of two wire serial interface for serial ID 5

4. LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. In the low state, the output will be pulled to less than 0.8V.

5. These are the differential receiver output. They are internally AC-coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES.

6. These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module.

Ordering information

HHD-G3115-2-LC 155M 1310/850nmnm 2KM/550M MM LC SFP 0~70 FP+PIN
HHD-G3115-20-LC 155M 1310nm 20KM SM LC SFP 0~70 FP+PIN
HHD-G3112-2-LC 1.25G 850nmnm 550M MM LC SFP 0~70 FP+PIN
HHD-G3112-20-LC 1.25G 1310nm 20KM SM LC SFP 0~70 FP+PIN
HHD-G3112-40-LC 1.25G 1310nm 40KM SM LC SFP 0~70 DFB+PIN
HHD-G3112-60-LC 1.25G 1310nm 60KM SM LC SFP 0~70 DFB+PIN
HHD-G3112-80-LC 1.25G 1310nm 80KM SM LC SFP 0~70 DFB+PIN
HHD-G3112-120-LC 1.25G 1310nm 120KM SM LC SFP 0~70 DFB+PIN